$15
Bestseller
mouse accessory
SKU DC-AC-APS-VEK
Arc PTFE Skates
SkatesCut per mouse0.8 mm
Pre-cut 100% PTFE skates. The everyday upgrade.
$15In stock
Fits: Vektor Air
3 mice
Arrives in 4–8 business days
US estimate: ships in 1–2 business days, then 3–6 in transit.
We ship to 25 countries — rates at checkout$84 more for free US shipping$99
Arc PTFE Skates
Vektor Air
0-01Arc PTFE Skates
Overview
Arc skates are cut from 0.8 mm sheets of 100% virgin PTFE and shaped to the exact outline of your mouse’s feet. Virgin PTFE has no recycled filler — the thing that makes cheap skates feel gritty — and every edge is rounded and polished, so the mouse slides over cloth seams and the border of the pad without catching.
The set drops into the stock recesses in minutes: peel the old feet, clean the recesses, press the new skates in. New PTFE settles in over the first hour or two of play and then glides evenly until it wears, and a complete spare set in the box covers a chipped skate or the next swap.
- 100% virgin PTFE, 0.8 mm
- Cut to your mouse’s feet
- Rounded, polished edges
- Spare set in the box
0-02Arc PTFE Skates
Compatibility(3)
Cut for Vektor Air, Orbit Pro and Pulse Mini. Each set follows the shell of one mouse, so a set for one does not fit another.
0-03Arc PTFE Skates
Swapping skates(4)
About 10 minutes, start to finish.
Lift the old skates
Slide the flat tip of a plastic pry tool under one end of a skate and lift it slowly, keeping the tool low. If it resists, warm it for a few seconds with a hair dryer to soften the adhesive. Never use a knife or a screwdriver: they gouge the shell and can scratch the sensor window.
Clean the recesses
Roll leftover adhesive off with your thumb, then wipe every recess with the alcohol prep pad and give it a minute to dry. Residue left in a recess makes the new skate sit high on one side.
Place the new set
Match each skate to its recess before you peel it — every piece fits one position only. Peel one at a time, hold it by the edges and lay it in from one end to the other, so no air is trapped. Keep your fingers off the adhesive.
Press and check
Press each skate firmly for 10 seconds: pressure is what bonds the adhesive. Set the mouse on the pad — it should sit flat without rocking. The bond keeps building for about a day.
TipNew PTFE can feel slightly scratchy for the first hour or two of play and settles as the surface polishes. Pre-polished and glass skates feel the same from the first swipe.
0-04Arc PTFE Skates
Specs(5)
Covered by a 12-month warranty.
- Type
- Skates
- Material
- 100% virgin PTFE
- Thickness
- 0.8 mm
- Edges
- Rounded, polished
- Adhesive
- 3M, pre-applied
In the box(3)
- One full set of skates for the chosen mouse
- Spare set
- Alcohol prep pad
0-05Arc PTFE Skates
Compare(5)
Every way we sell to make a mouse glide, side by side — each in its version for your mouse.
- Skates · this pageArc PTFE Skates
- Material
- 100% virgin PTFE
- Thickness
- 0.8 mm
- Fits
- Cut per mouse
$15 - SkatesArc Pro Skates
- Material
- 100% virgin PTFE
- Thickness
- 1 mm
- Fits
- Cut per mouse
$19 - SkatesPrism Glass Skates
- Material
- Chemically tempered glass
- Thickness
- 0.6 mm
- Fits
- Cut per mouse
$35 - Dot skatesArc Dot Skates
- Material
- 100% virgin PTFE
- Thickness
- 0.8 mm
- Fits
- Any mouse
$15 - Dot skatesPrism Glass Dots
- Material
- Chemically tempered glass
- Thickness
- 0.6 mm
- Fits
- Any mouse
$24
0-06Arc PTFE Skates
Questions(8)
Still unsure? Write to [email protected] — we reply within one business day.
Choose yours under “Fits”: Vektor Air, Orbit Pro or Pulse Mini. Each set is cut for that one shell, so a set for one mouse won’t fit another — or another brand’s mouse.
for Vektor Air
Complete the upgrade(4)
The rest of the kit for Vektor Air: one of each kind, each in its version for that mouse.
your mouse
Vektor AirOrbit ProPulse Mini
$15
$19
$19
More gear(4)
Onyx$109In stock · ships in 1–2 business days
NewInk$49In stock · ships in 1–2 business days
Bestseller
Obsidian$79In stock · ships in 1–2 business days