$15
mouse accessory
SKU DC-AC-APR-VEK
Arc Pro Skates
SkatesCut per mouse1 mm
1.0 mm pre-polished PTFE. Made for soft, thick pads.
$19In stock
Fits: Vektor Air
3 mice
Arrives in 4–8 business days
US estimate: ships in 1–2 business days, then 3–6 in transit.
We ship to 25 countries — rates at checkout$80 more for free US shipping$99
Arc Pro Skates
Vektor Air
0-01Arc Pro Skates
Overview
Arc Pro is 1.0 mm of virgin PTFE, made for soft and thick cloth pads where thinner feet sink into the foam under a heavy hand. The extra height keeps the base of the mouse clear of the weave, and the extra material means a set takes longer to wear through.
Every skate is pre-polished and shaped with a curved edge — a wide radius all the way round instead of a small chamfer — so the leading edge doesn’t dig in when you press down on a flick, and the glide is smooth from the first session instead of after a few hours of settling in. On a glass pad, where PTFE wears fastest, the thickness buys you the most time.
- 1.0 mm PTFE for soft, thick pads
- Pre-polished: smooth from day one
- Curved edge profile
- More material, longer life
0-02Arc Pro Skates
Compatibility(3)
Cut for Vektor Air, Orbit Pro and Pulse Mini. Each set follows the shell of one mouse, so a set for one does not fit another.
0-03Arc Pro Skates
Swapping skates(4)
About 10 minutes, start to finish.
Lift the old skates
Slide the flat tip of a plastic pry tool under one end of a skate and lift it slowly, keeping the tool low. If it resists, warm it for a few seconds with a hair dryer to soften the adhesive. Never use a knife or a screwdriver: they gouge the shell and can scratch the sensor window.
Clean the recesses
Roll leftover adhesive off with your thumb, then wipe every recess with the alcohol prep pad and give it a minute to dry. Residue left in a recess makes the new skate sit high on one side.
Place the new set
Match each skate to its recess before you peel it — every piece fits one position only. Peel one at a time, hold it by the edges and lay it in from one end to the other, so no air is trapped. Keep your fingers off the adhesive.
Press and check
Press each skate firmly for 10 seconds: pressure is what bonds the adhesive. Set the mouse on the pad — it should sit flat without rocking. The bond keeps building for about a day.
TipNew PTFE can feel slightly scratchy for the first hour or two of play and settles as the surface polishes. Pre-polished and glass skates feel the same from the first swipe.
0-04Arc Pro Skates
Specs(5)
Covered by a 12-month warranty.
- Type
- Skates
- Material
- 100% virgin PTFE
- Thickness
- 1.0 mm
- Edges
- Curved, pre-polished
- Adhesive
- 3M, pre-applied
In the box(2)
- One full set of skates for the chosen mouse
- Alcohol prep pad
0-05Arc Pro Skates
Compare(5)
Every way we sell to make a mouse glide, side by side — each in its version for your mouse.
- SkatesArc PTFE Skates
- Material
- 100% virgin PTFE
- Thickness
- 0.8 mm
- Fits
- Cut per mouse
$15 - Skates · this pageArc Pro Skates
- Material
- 100% virgin PTFE
- Thickness
- 1 mm
- Fits
- Cut per mouse
$19 - SkatesPrism Glass Skates
- Material
- Chemically tempered glass
- Thickness
- 0.6 mm
- Fits
- Cut per mouse
$35 - Dot skatesArc Dot Skates
- Material
- 100% virgin PTFE
- Thickness
- 0.8 mm
- Fits
- Any mouse
$15 - Dot skatesPrism Glass Dots
- Material
- Chemically tempered glass
- Thickness
- 0.6 mm
- Fits
- Any mouse
$24
0-06Arc Pro Skates
Questions(8)
Still unsure? Write to [email protected] — we reply within one business day.
Choose yours under “Fits”: Vektor Air, Orbit Pro or Pulse Mini. Each set is cut for that one shell, so a set for one mouse won’t fit another — or another brand’s mouse.
for Vektor Air
Complete the upgrade(4)
The rest of the kit for Vektor Air: one of each kind, each in its version for that mouse.
your mouse
Vektor AirOrbit ProPulse Mini
$15
$19
$19
More gear(4)
Onyx$109In stock · ships in 1–2 business days
NewInk$49In stock · ships in 1–2 business days
Bestseller
Obsidian$79In stock · ships in 1–2 business days